Contact us today:
(847) 934-4500
tdaro@bernardandcompany.com
Contact us today:
(847) 934-4500
tdaro@bernardandcompany.com
This Grieve oven is a 550°F (288°C) new truck oven customized from the standard TCH-550 model and is currently used for heat processing parts at the customer’s facility. Workspace dimensions of this oven measure 60” W x 60” D x 60” H. 30 KW are installed in Incoloy sheathed tubular heating elements, while a 2000 CFM, 2 HP recirculating blower provides horizontal airflow to the workload.
This Grieve truck oven has 6” insulated walls, an aluminized steel interior and aluminized steel exterior with enamel finish. Features include a purge timer, two-position dampers on fresh air inlet and exhaust outlet and a 1200 lb. capacity stainless steel loading truck. Additional features include a 325 CFM powered forced exhauster with an airflow safety switch. The oven includes all safety equipment required by NFPA Standard 86, IRI, FM and OSHA.
Controls on this Grieve oven include a UL listed control panel, a programmable temperature controller, SCR power controller, a circular chart recorder and a circuit breaker disconnect switch mounted through control panel door.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 976 is a 500ºF (~260ºC) electrically-heated jumbo walk-in oven from Grieve, currently used for heating molds at the customer’s facility. Workspace of this unit measures 13’W x 28’D x 7’6”H. 360KW are installed in Incoloy sheathed tubular elements to heat the oven, while 49,000CFM from two 20HP recirculating blowers provide a combination airflow to the workload.
This Grieve jumbo walk-in oven features 4” thick insulated walls, removable top-mounted heat chamber (shown in the right foreground of the attached photo), aluminized steel interior and exterior, door seals eliminated and doors equipped with drag seals, plus the unit was constructed to split into four sections for shipment to the customer’s location.
Oven controls on No. 976 include a 13,500CFM powered forced exhauster (shown in the left foreground of the attached photo) and other safety equipment required to handle up to two gallons of flammable solvent at 370ºF (~188ºC). Also onboard are a digital programming temperature controller, SCR power controller and motorized dampers on the intake and exhaust for accelerated cooling and rapid purging. This Grieve jumbo walk-in was built to NEMA 12/NFPA 79 electrical standards.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 942 is a 350°F (177°C), special walk-in oven from Grieve, currently used for curing epoxy at the customer’s facility. Workspace dimensions of this oven measure 84” W x 144” D x 108” H. 400,000 BTU/hour are installed in a modulating natural gas burner, while a 12,000 CFM total are provided by two (2) 5-HP recirculating blowers providing combination airflow to the workload.
This Grieve oven features 4” insulated walls, aluminized steel interior and exterior and three (3) independent doors for access to workspace on front with standard double doors on rear. Additional features include 2” insulated floor with three (3) pairs of truck wheel guide tracks. The oven is raised above factory floor level on 6” I-beams.
The oven features all safety equipment required by IRI, FM and National Fire Protection Association Standard 86 for gas heated equipment, including a 325 CFM, 1/3-HP powered forced exhauster.
Controls on the No. 942 include a digital programming temperature controller and 10” diameter circular chart recorder.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 958 is a 500° (260°C), electrically heated walk-in oven from Grieve, currently used for heat treating long fluorocarbon shapes supported by fixtures on wheels at the customer’s facility. Workspace dimensions of this oven measure 36” W x 300” D x 36” H. 60KW are installed in lncoloy sheathed tubular heating elements, while a 4200 CFM, 3-HP recirculating blower provides combination airflow to the workload.
This Grieve walk-in oven has 4” insulated walls and an aluminized steel interior and exterior. Features include an integral top mounted heat chamber, single door front and rear, 2” insulated floor with channel guide tracks and two (2) fixture supports with flanged wheels.
Controls on No. 958 include a digital programming and recording temperature controller, manual reset excess temperature controller with separate contactors plus recirculating blower airflow safety switch and SCR power controller.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 978 is a 500ºF, electrically-heated, two-compartment universal style oven from Grieve, currently used for various machine shop operations at the customer’s facility. Workspace dimensions of this oven measure 30” W x 36” D x 36” H in each of the two heating zones. 6.6 KW per zone (13.2 KW total) are installed in Nichrome wire elements to heat the oven chamber, while a 600 CFM, 1/2-HP recirculating blower provides front-to-rear universal airflow to the workload.
This Grieve universal oven features 4” insulated walls, aluminized steel exterior, Type 304, 2B finish stainless steel interior, double doors and an integral leg stand.
Controls on No. 978 include a digital indicating temperature controller in each compartment of the oven, manual reset excess temperature controllers with separate contactors, recirculating blower airflow safety switches and a 10” diameter circular chart recorder, one per compartment, to record part temperatures.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 864 is a 350ºF, natural gas-heated belt conveyor oven from Grieve, currently used for drying gold ore samples at the customer’s facility. Workspace dimensions of this oven measure 6-1/2’ W x 35’ D x 1-1/2’ H. 1,650,000 BTU are installed in a modulating natural gas burner to heat the oven chamber, while a 24,500 CFM, 20 HP recirculating blower provides vertical downward airflow to the workload.
This Grieve oven features a 5’ long open belt loading zone, 35’ long insulated heat zone with recirculated airflow and 1’ long open belt unloading zone, plus 4” insulated walls, aluminized steel interior and exterior. A 6’ wide, 1” x 1” galvanized steel, flat wire conveyor belt with ¼ HP motor drive, variable from 5 to 50 feet per hour, transports the workload. Side access doors are provided along the length of the workspace to inspect the load and service the heating chamber.
All safety equipment required by IRI, FM and NFPA Standard 86 for gas-heated equipment are provided on this belt conveyor oven, including a 1500 CFM, 2 HP powered forced exhauster.
Controls on No. 864 include a conveyor belt start/stop, digital indicating current proportioning temperature controller, manual reset excess temperature controller, variable SCR drive to control conveyor belt speed, pilot lights to indicate when blower and heat are energized, pushbutton electronic ignition, on-off heat switch and main oven control pushbuttons. The NEMA 12 control panel is equipped with a lockable fused disconnect switch.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 1033 is a 500ºC (932ºF) inert atmosphere oven from Grieve, currently used for heating polymer fibers at the customer’s facility. Workspace dimensions of this oven measure 54” W x 36” D x 84” H. 60 KW are installed in Incoloy-sheathed tubular elements to heat the oven chamber, while a 10,000 CFM, 7-1/2 HP recirculating blower provides vertical downward airflow to the workload.
This Grieve oven features 8” thick insulated walls plus an aluminized steel exterior and Type 304, 2B finish stainless steel interior. The inert atmosphere construction comprises a gas pressure regulator, flow meter, pressure gauge, internal high-temperature gasket, all welded expansion connection in doorway throat, air jacket on inner oven for cooling, ½” thick cellular silicone rubber atmosphere seal, blower shaft seal, pneumatic positive latching door hardware, adjustable offset door hinges, outlet with pressure relief, interior seams all welded gas-tight plus all wall penetrations are fitted with compression fittings. A 0-1500 CFM blower pulls air through the air jacket on the inner oven for faster cooling.
Controls on No. 1033 include a digital programming temperature controller, manual reset excess temperature controller with separate contactors, recirculating airflow safety switch, paperless event recorder, SCR power controller and trace level oxygen analyzer.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 1008 is a 500ºF tunnel oven with gravity roller conveyor from Grieve, currently used for preheating metal housings at the customer’s facility. Workspace dimensions of this oven measure 42” W x 72” D x 30” H. 30 KW are installed in Incoloy-sheathed tubular elements to heat the oven chamber, while a 3000 CFM, 1-1/2 HP recirculating blower provides vertical downward airflow to the workload.
This Grieve tunnel oven features 4” thick insulated walls plus an aluminized steel interior and exterior. The work zone comprises a 66” long open loading zone, 72” long insulated heat zone with recirculated airflow and 66” long open unloading zone, with a 36” wide roller conveyor with rollers on 3” centers. Motor-operated vertical lift doors are supplied on each end of the oven.
Controls on No. 1008 are built to NEMA 12 electrical standards and include a digital indicating temperature controller, manual reset excess temperature controller with separate contactors and a recirculating blower airflow safety switch.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No.996 is a gas-fired, 350ºF (177ºC) jumbo walk-in oven, currently used for batch processing large composite structures. Workspace dimensions measure 10’ W x 32’ D x 8’ H. 1,200,000 BTU/HR are installed in a modulating natural gas burner to heat the unit, while 49,000 CFM total from two (2) 20HP recirculating blowers provide combination airflow to the workloads.
This Grieve jumbo walk-in batch oven features 4” insulated walls throughout, removable top-mounted heat chamber (shown removed in photo), the oven body split into four
(4) sections for shipment with mating angle iron frames for easy reassembly in the field, plus aluminized steel interior and exterior.
All safety equipment required by IRI, FM and National Fire Protection Association Standard 86 for gas-heated equipment are onboard No. 996, including an 8000 CFM powered forced exhauster for quick purge and cool down, motorized dampers on the intake and exhaust for accelerated cooling, as well as a 10” diameter circular chart recording and programming temperature controller.
For more information, please contact:
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, IL 60073-2898
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese, VP
No. 871 is a 2000°F (~1093.3°C) gas-heated box furnace from Grieve, currently used for heat treating and high temperature testing. 650,000 BTU/HR are installed in three modulating natural gas burners with a floor mounted combustion air blower. Workspace dimensions are 30” wide x 48” deep x 30” high.
The unit has 7” insulated walls comprised of 5” of 2300°F ceramic fiber and 2” of 1700°F block insulation. The 6½” floor insulation is made of 4½” of 2300°F firebrick and 2” of 1900°F block insulation. The plate hearth is made of firebrick and is supported by firebrick piers.
For more information, please contact:Controls onboard No. 871 include a Partlow MRC 7000 recording and programming temperature controller and an electrically-operated vertical lift door.
THE GRIEVE CORPORATION
500 Hart Road
Round Lake, Illinois 60073-2835
USA
Phone: (847) 546-8225
Fax: (847) 546-9210
Web: www.grievecorp.com
Email: sales@grievecorp.com
Attention: Frank Calabrese